INJECTION & VENT PORTS (click picture to shop for ports)
MOLD MAKING ACCESSORIES (click picture to shop for accessories)
Infuser LRTM Vacuum System DT08
The Infuser DT08 RTM Light Vacuum system is designed specifically for your closed molding needs. You will find DT08 dual vacuum pump system capable to supporting 6 or more Large molds in a production LRTM environment.
The design of this system is built on the extremely reliable Becker vacuum pumps, to which we will supply one model U 4.2 wet type high vacuum pump for the flange vacuum to ensure the highest possible clamping force while still allowing for enough capacity to over come leaks that are typical to production tooling in the LRTM process.
The second Becker pump will be the VT 4.40 which is a dry type vacuum pump complete with the adjustable vacuum setting valve to allow for the needed adjustment of the cavity vacuum.
The dual pump design far out performs the alternative to have one vacuum pump, with a separate pump for the clamping flange vacuum, and one for the cavity vacuum, allows for the clamping vacuum to be maintained even if the cavity vacuum is drained from open lines through operator error. Also, each pump is lubricated with a proprietary lubricant which is compatible with the styrene vapors as common to the LRTM process.
Both pumps are mounted on a common steel box tube stand which has a powdered coated finish. In addition to the two each vacuum pumps are dual 20 gallon receiver tanks one for the flange vacuum to aid in quick draw down and to aid in recovery of intermittent leaks, the second for the cavity vacuum.
Also, each vacuum system will have a separate vacuum 4” gauge which is mounted plain view for confirmation of vacuum settings for both the cavity and flange vacuum.
The specifications of each pump are listed below and in addition to the pumps will be a common 3ph motor (either 240 or 480 vac) and a common Start & Stop button.
Becker Model U 4.2 SA Rotary Vane Vacuum Pump and Motor.
Capacity: 12.6 SCFM open flow, Maximum Vacuum 2 Torr ( 29.84” Hg)
Description: Oil flooded rotary vane vacuum pump with two stage
oil separation, pressure differential lubrication, integrated anti-suck
back valve, horizontally mounted inlet filter, and integrally flanged
to a 0.9 HP, 1700 RPM, Wide Range Voltage, 3 ph., 50/60 Hz. motor.
Becker Model VT 4.40 Rotary Vane Vacuum Pump and Motor.
Capacity: 28 SCFM open flow, Maximum Vacuum 25.5” Hg
Description: Oil less rotary vane vacuum pump with carbon vanes, built-in
suction filter, vacuum regulating valve, w/ remote inlet filter and integrally flanged to a 1.67/2.0 HP, 1430/1750 RPM, Wide Range Voltage, 3 ph., 50/60 Hz. IP 54, motor.
This vacuum system as designed will allow for convenient mounting on the plant floor as well as easy connection to a PVC plant vacuum header system
(Note: Vacuum header not included but is typically made from common PVC pipe and fittings, either schedule 40 or 80 PVC can be used.)
The cost of the system as described is$7,026.00F.O.B. Fenton Michigan.
Domestic Payment Terms: International Terms:
50% Down with Purchase Order T.T. Bank 50% with Purchase Order
50% When Ready to Ship T.T. Bank 50% When Ready to Shi
EQUIPMENT WARRANTY
All products manufactured by JHM Technologies, Inc. are warranted under normal usage and service against defects in workmanship or materials for a period of 6 months from the date of shipment. JHM Technologies, Inc. will repair or replace at its option any product or assembled components it finds to be defective.
This warrantee is limited to the cost of the original product and is in lieu of all other express or implied warranties and excludes the loss of profits, or any other direct or indirect incidental or consequential damages caused by product failure or delay in remedying the same.
This warrantee shall not be enforceable if the purchaser is in default, or delay, in making full payment for products purchased from JHM Technologies, Inc.
This warranty does not cover failures caused in whole or in part, but not necessarily limited, to the under noted causes:
Improper application
Operation outside of design limitation
Low / high air supply <85 psi >125 psi
Low / high voltage + 6% or rated voltage
Power interruptions, phase failure / reversal, or power spikes
Product is used with resins, catalyst or solvents that are not compatible with the materials of construction or authorized by manufacture
Product failure attributed to dirt, moisture or foreign bodies entering the system
Misuse by operation not in strict accordance with instruction manual
Claims for products subject to failure within the terms of this warrantee must be submitted in accordance to the following procedure;
The purchaser must notify JHM Technologies, Inc. of the product failure with 5 working days of the failure and request a return material authorization (RMA) number which will be used to identify the claim once the defective item is returned for inspection in accordance with the terms listed above. Included in the return shipment is to be the full report associated with the product failure, including the JHM Technologies, Inc. product serial number. Accompanying the returned product for WARRANTEE INVESTIGATION is to be a purchaser’s purchase order for the replacement item. If in the event of the product not being repairable and pending evaluation of the claim; JHM Technologies, Inc. at their discretion may provide a replacement product F.O.B. point of origin, which would be invoiced to the purchaser in the normal manner. If the purchaser’s claim is accepted within the scope of the warranty, a credit note will be issued within 30 days of approval.
Should the claim in our opinion fall outside the terms of the warranty period, due to any of the aforementioned exclusions, or through the late submittal of claim, lapse of warranty period, or any reasonable justification giving JHM Technologies, Inc. cause to reject the claim; then no credit note will be issued and the full invoice value will become due within the purchaser’s agreed payment terms
